纳士达 都百特 鑫工艺

热加工行业论坛

 找回密码
 免费注册

QQ登录

只需一步,快速开始


查看: 4384|回复: 0

[其它] PLC常用专业英文词汇

[复制链接]
  • TA的每日心情
    奋斗
    2021-9-22 07:19
  • 签到天数: 49 天

    连续签到: 2 天

    [LV.5]常住居民I

    发表于 2019-9-20 21:32:31 | 显示全部楼层 |阅读模式

    马上注册,结交更多热工坛友,更多精彩内容等着您!

    您需要 登录 才可以下载或查看,没有帐号?免费注册

    x
    一、a开头
    absolute 绝对位置
    Absolute output 绝对最大输出
    actuator 执行器/作动器
    against 对比
    allocate 分配
    alter 改变/修改
    ambient 环境周围
    ambient operating temperature
    analog 模拟
    analysis 分析
    applicable 可用
    assign 分配

    二、b开头
    back up battey 备用电池
    barcode reader/ID 条形码阅读器
    base unit 主基板
    baud 波特
    beforehand 事先
    binary 二进制
    buffer memory 缓冲存储器
    bus 总线

    三、c开头
    case 外壳
    characteristic 特征
    check 校验
    child-station 子站
    common terminal 公共端
    compatible 兼容
    compound 混合
    condensation 结露
    condition 条件
    conductive 导电
    configuration 组态
    configure 组态
    confirm 确认
    consumption 消耗
    content 目录
    control level 控制级
    convenient 方便
    conventionaly 传统
    conversion 转换
    converter 转换器
    conveyor 传送
    corrosive 腐蚀
    cutoff 切断
    countermeasure 对策

    四、d开头
    debug 调试
    dedicated 屏蔽
    dedicated 专用
    default value 缺省值
    define 解释/阐明
    design 设计
    device level 现场级
    diagnosis 诊断
    digital 数字
    din rail 导轨
    diverse 不同的/各种各样的
    download 下载
    duplicate 完全一样
    dust 灰尘

    五、e开头
    eliminate 免得
    enterprise level 管理级
    erase 清除
    exceed 超出
    execute 执行
    expand 扩展

    六、f开头
    faulty 故障站
    field bus 现场总线
    fix 固定
    flexibly 灵活的
    flow 流量
    format 格式
    fuse 融丝

    七、g开头
    graph图标坐标图曲线
    guaranteed 担保

    八、h开头
    handle 处理
    hardware manual 硬件手册
    hint 提示
    humidity 湿度

    九、i开头
    individual 独立的
    inductance 电感
    initiate 实施发起
    input 输入
    input point 输入点数
    install 安装
    instruction 指令
    insulation 隔离
    interface 接口
    interlocking 互锁
    internal 内部
    interrupt 中断
    invalid 无效

    十、m开头
    magnetic 有磁性的
    main circuit 主回路/线电路
    malfunction 故障
    mandatory 强制
    mantenance 维护
    manual 手册
    mechanical 机械
    mechanical life 机械寿命
    module 模块/组件
    momentary power failure 瞬时断电
    monitor 监视
    mount 固定
    multiple 多样

    十一、n开头
    negative 负

    十二、o开头
    observation 观察
    occupy 占用
    occur 发生
    offline 离线
    offset gain 偏置增益
    oil mist 油雾
    optical loop 光缆回路
    optimum 最佳的
    output 输出
    overall 总的
    overview 总揽

    十三、p开头
    parameter 参数
    path 路径
    perform 进行
    performance specifations 性能规格
    peripheral 外围/外部设备
    phase 相
    point 要点
    port 接口
    positive 正
    power line 电源线
    power>precaution 注意事项
    print board 印刷电路板
    procedure 过程
    programing interface 编程接口/编程界面
    protocol 协议

    十四、r开头
    range 范围
    rated input voltage 额定输入电压
    ratio 比率
    refer to 参照
    recommend 建议
    reduce 减少/缩小
    register 数据寄存器
    relay 继电器
    remote I/O 远程网络
    reserved station 预留主站
    resistor 电阻器

    十五、l开头
    load bridging resistor 负载转移电阻
    load compensating resistor 负荷补偿电阻
    load shifting resistor 负载移动电阻器 ; 负荷转移电阻
    load-resistor contactor 负载电阻器接触器 ; 负荷电阻接触器
    anode load resistor 释义阳极负载电阻 ; 阳极负载电阻
    effect of load resistor 负载电阻效应

    十六、r开头
    resolution 分辨率
    Maximum resolution 最大分辨率
    restriction 限制
    retry 重试

    十七、s开头
    scan 扫描
    screw 螺丝
    seamless network 无缝网络
    sequence programme 顺控程序
    serial communications module 串口通信模块
    series 系列
    servo 伺服系统
    short 短路
    signal 信号
    sink 漏极
    slot 周边元件扩展插槽
    soures 源极
    specifications 特性
    stabilized power supply 稳压电源
    standby master station 备用主站
    start up 起动
    status 状态
    step drive 步进
    storage 存储
    store 存储
    witch off 切断
    swith 开关

    十八、t开头
    table 表格
    transfer 传送
    transistor 晶体管
    transmission speed 传输速度
    transmit 传送/传输
    triac 三端双向可控硅开关元件
    troubleshooting 故障处理

    十九、u开头
    unuseble 不可以使用
    upload 上传/上载
    utilize 利用

    二十、v开头
    verify 校验
    voltage 电压

    二十一、w开头
    watchdog 看门狗定时器
    width 范围
    wire chips 线头
    您需要登录后才可以回帖 登录 | 免费注册

    本版积分规则

    QQ|手机版|Archiver|热加工行业论坛 ( 苏ICP备18061189号-1|豫公网安备 41142602000010号 )
    版权所有:南京热之梦信息技术有限公司

    GMT+8, 2024-3-29 18:10 , Processed in 0.125313 second(s), 22 queries .

    Powered by Discuz! X3.4

    Copyright © 2001-2020, Tencent Cloud.

    快速回复 返回顶部 返回列表